Adlink cPCIS-2500 Series Uživatelský manuál

cPCIS-2501 3U CompactPCI 6-slot Cubic Chassis User’s Guide

This page intentionally left blank.

Getting Started • 5 2 Getting Started In this chapter, we will describe the unpacking procedure for the cPCIS-2501 and installation procedures for Co

6 • Getting Started CompactPCI Card Installation/Removal Procedure 1. Place the chassis on a level surface. Remove the blanking plates where requir

Getting Started • 7 To remove the module, press the locking button (if necessary), and reverse steps 1 through 5 above. System Card Fully Inserte

8 • Getting Started CompactPCI PSU Installation/Removal Procedure The installation and removal procedures for a CompactPCI PSU are the same as those

Getting Started • 9 2.3 Powering Up the System Set the main power switch in the lower right corner of the rear panel to the off position ( O ). Set

This page intentionally left blank.

Backplane • 11 3 Backplane In this chapter, we will describe the backplanes for the cPCIS-2501, the cBP-3206 is a 3U CompactPCI 32-bit backplane and

12 • Backplane Mechanical Drawing cBP-3206 RearViewcBP-3206 Front View1 - P21 - P16 - P26 - P1CN1 CN2 JP8 - JP10

Backplane • 13 Pin Assignment ¾ [1 – P1] System Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND24 GND AD[1] +5V V(I/O)

This page intentionally left blank.

14 • Backplane ¾ [1 – P2] System Slot Pin Z A B C D E F 22 GND GA4 GA3 GA2 GA1 GA0 GND21 GND CLK6 GND NC NC NC GND20 GND CLK5 GND NC NC NC

Backplane • 15 ¾ [2 – P1] – [6 – P1] Peripheral Slot Pin Z A B C D E F 25 GND +5V REQ64# ENUM# +3.3V +5V GND 24 GND AD[1] +5V V(I/O) A

16 • Backplane ¾ CN1 / CN2 – ATX Power Connector Pin Signal Pin Signal 1 +3.3V 11 +3.3V 2 +3.3V 12 -12V 3 GND 13 GND 4 +5V 14 PS_ON_L 5 GND 15

Backplane • 17 3.2 cBP-3061 Power Backplane The cBP-3061 is a PICMG 2.11 CompactPCI 3U 47-pin power backplane for one power module. It is used by the

18 • Backplane Pin Assignment ¾ CN1 – Power Sense Connector Pin # Signal Name 1 V1_Sense 2 GND_S 3 V2_Sense 4 V3_Sense 5 NC ¾ CN2 – Power Sense

Backplane • 19 ¾ CN4 – Modular Power 47P Connector Pin Signal Pin Signal 47 ACL/-DC IN 31 GA2 46 ACN/+DC IN 30 V1 SENSE 45 CGND 29 V1ADJ 44

20 • Backplane ¾ CN7 –AC/DC in Let Connector Pin # Signal Name 1 ACN/DC+ 2 ACL/DC- 3 CGND ¾ CN8 – IPMB Connector Pin # Signal Name 1 IPMB_SCL

Cooling System • 21 4 Cooling System The cPCIS-2501 is equipped with two bottom access removable fans for intake to provide an effectively cooled envi

22 • Cooling System 2. Lift the grill and attached fan module out of the chassis. Remove the remaining two screws attaching the fan module to the g

Cooling System • 23 4.2 Fan Removal and Replacement To remove the fan module from the chassis, follow the Air Filter Removal and Replacement Procedu

©Copyright 2005, 2010 ADLINK Technology Inc. All Rights Reserved. Manual Rev. 1.01, November 10, 2010 Part Number: 50-15041-1010 The information

This page intentionally left blank.

Power Supply Unit • 25 5 Power Supply Unit The cPCIS-2501 is equipped with ADLINK’s cPS-H325/AC CompactPCI power module. 5.1 CompactPCI: cPS-H325/AC

26 • Power Supply Unit Input Characteristics • Input Voltage: Typ. 90-264VAC • Power Factor Correction: Meets Harmonic Correction IEC1000-3-2. Power

Power Supply Unit • 27 Symbol: "★" OVP built-in; "@" Adjustable; "#" Remote sensing; "≡" 3rd-wire Load Sh

This page intentionally left blank.

Important Safety Instructions • 29 Important Safety Instructions Read and follow all instructions marked on the product and in the documentation befor

30 • Important Safety Instructions z Lithium Battery provided (real time clock battery) “CAUTION – Risk of explosion if battery is replaced by an inc

Getting Service from ADLINK Customer Satisfaction is top priority for ADLINK TECHNOLOGY INC. If you need any help or service, please contact us. ADLIN

Table of Contents • v Table of Contents 1 Introduction ...1 1.1 Pro

This page intentionally left blank.

Introduction • 1 1 Introduction 1.1 Product Definition The cPCIS-2501 3U CompactPCI 6-slot Cubic Chassis is designed for 3U CompactPCI cards and modul

2 • Introduction 1.2 Features • Compact size, 4U high enclosure for 3U CompactPCI cards w/o rear I/O • Board Space: 1 system slot, 5 peripheral slot

Introduction • 3 1.4 Mechanical Drawing cPCIS-2501 Front ViewcPCIS-2501 Side View